Audio & TechnicalUtility
Runs in your browser

LUFS Meter & Podcast Loudness Checker

Drop in an episode to see its integrated LUFS, true peak and loudness range in seconds. Compare the result with the Apple Podcasts and Spotify targets and get the exact gain change you need. The file is measured on your device and never uploaded.

100% Client-Side Memory
2026 Industry Spec Verified
Target

What the LUFS Meter does

The LUFS Meter measures how loud an episode really is. It reads the integrated loudness in LUFS, the true peak in dBTP and the loudness range, using the ITU-R BS.1770 method that podcast and streaming platforms rely on.

It then compares your file with a platform target and tells you how many decibels to raise or lower the level. The audio is decoded and measured in your browser, so the file never leaves your device.

How to use it

  1. Pick a target

    Choose Apple Podcasts (−16 LUFS), Spotify (−14 LUFS) or the broadcast standard (−23 LUFS).

  2. Drop in your file

    Add the exported episode as MP3, WAV, M4A, FLAC or OGG. Measuring a long episode can take a few seconds.

  3. Read the result

    Check integrated loudness and true peak against the target, and scan the timeline for sections that are much louder or quieter.

  4. Adjust and re-export

    Apply the suggested gain change in your editor, use a limiter if the peak gets too high, then measure the new file.

Tips for better results

  • Measure the final exported file, not the project. Encoding to MP3 can raise the true peak slightly.
  • For a mono file, aim for about −19 LUFS measured as a single channel. It plays as loud as a −16 LUFS stereo file.
  • A loudness range above roughly 10 LU often means quiet passages will be hard to hear in a car or on a train. Gentle compression helps.

What is −16 LUFS and why does it matter for podcasts?

LUFS (Loudness Units relative to Full Scale) measures the perceived loudness of a whole file instead of its highest peak. Apple Podcasts asks for an overall loudness of around −16 dB LKFS, with a tolerance of ±1 dB and a true peak no higher than −1 dBFS. LKFS and LUFS are the same unit under two names.

Spotify adjusts playback to −14 LUFS, so many podcasters still deliver at −16 LUFS and let each app make its own adjustment. Staying near the target keeps your show at a similar volume to the episodes played before and after it, so listeners do not have to reach for the volume control.

Proper microphone gain staging & hardware setup: Best Podcast Equipment for Beginners →

Related Production Tools

Frequently Asked Questions

Answers to common questions about privacy, pricing, and how the tools work.

What LUFS should a podcast be?
Apple Podcasts recommends an overall loudness of about −16 LUFS, within ±1 dB, and a true peak no higher than −1 dBFS. Spotify adjusts playback to −14 LUFS. Many podcasters master to −16 LUFS so that one file works in every app.
How do I measure the LUFS of an audio file?
Drop the exported file into the meter. It decodes the audio in your browser, applies the K-weighting filter and gating defined in ITU-R BS.1770, and reports integrated loudness, true peak and loudness range. Nothing is uploaded.
Why does my mono file read −19 LUFS instead of −16?
A mono file measured as a single channel reads about 3 LU lower than the same audio in two channels. Players send mono to both speakers, so a −19 LUFS mono file sounds as loud as a −16 LUFS stereo file. The meter shows both values for mono files.
What is the difference between LUFS and true peak?
LUFS describes the average perceived loudness of the whole file. True peak is the highest level the waveform reaches once it is converted back to analog, including peaks between samples. A file can hit the loudness target and still distort if its true peak is too high.
Does this tool change or normalize my audio?
No. It only measures. It tells you how many decibels to raise or lower the level, and you apply that change in your audio editor. True peak is an estimate based on 4× oversampling, so leave a small safety margin.